You feel a wooden floor with your feet. We build that feeling in, wherever in the Canary Islands someone loves wood as much as we do.
Parquet fitting and solid wood floorboards in hardwood: herringbone, basket weave, random bond or wide boards. We measure the subfloor, glue down the full surface and travel to every one of the Canary Islands to do it.
We only lay timbers that are naturally resistant. Our benchmark is the European standard EN 350. It sorts wood into five durability classes, from 1 (very durable) to 5 (not durable). We work with classes 1 and 2, always heartwood, never sapwood.
With solid floorboards, the subfloor decides everything. We measure the residual moisture of the screed, let the wood acclimatise in the room and glue the boards down over the full surface. The boards sit fully supported, do not sound hollow and leave no cavity where moisture can collect. We stagger the head joints of adjacent rows by at least twice the board width, and never by less than 25 cm.
Mosaic parquet is wood through and through, with no softwood core. The material costs less than floorboards. But it takes craft: the fingers are glued on site, sanded, filled and oiled or lacquered. If you were thinking of vinyl, this is real wood instead.
Teak copes with water like few other timbers. That is why we also lay it where you would usually find tiles: in bathrooms and showers, on balconies and terraces. Barefoot it feels warm, not cold. We only use teak from certified plantations.
A pattern changes a room more than any colour. We lay:
Parallel strips, head joints staggered irregularly, at least 20 cm apart between adjacent rows. Calm, suits any room.
Head joints always offset by half a strip. Clear and orderly.
Strips interlocked at right angles. The classic.
Strips cut at an angle, meeting in a point. Very elegant, demanding to lay.
Squares of parallel strips, usually seven, each square turned 90 degrees.
A frame in a second timber, for any pattern.
A wooden floor is only as good as what it sits on. Before every parquet fitting we measure three things:
If there is underfloor heating in the screed, we heat it up and cool it down to protocol first. Only when the readings are right do we glue. That is our principle “Know first, then build.”, applied to the floor.
Solid wood is wood through and through. It has no softwood core and no thin wear layer that is gone after one sanding. A solid floor can be sanded and re-oiled several times. It is not replaced, it is restored. Timbers in classes 1 and 2 are also naturally resistant to moisture, fungi and insects.
There are termites in the Canary Islands. The introduced subterranean termite is documented on Tenerife and Lanzarote, where it attacks timber in houses; the Cabildo of Tenerife has been fighting it for years.
For floors this means: engineered parquet and click floors usually have a core of softwood or wood-based board. A solid floor in durable hardwood, glued over the full surface, offers less to attack and no cavity. So wherever termites are an issue, we recommend solid wood.
We are based on La Gomera. For fitting we travel to Tenerife, Gran Canaria, La Palma, El Hierro, Lanzarote and Fuerteventura. Advice in English.
We buy only certified wood (FSC or PEFC) from specialist suppliers in the EU.
An old wooden floor is often better than its reputation. Before it is ripped out, we take a look. Often restoring it is enough:
First we check whether the wood is dry and firm and how much wear layer is left. Only then do we tell you whether restoring is worth it or a new floor is the better choice.
Solid. It has no softwood core, can be sanded several times and, in durable timbers, is naturally resistant. Engineered parquet is quicker to lay and cheaper. Where termites or high humidity are an issue, we recommend solid wood.
Only timbers in durability classes 1 and 2 to EN 350: merbau, teak, oak, sweet chestnut; on request doussié and robinia. Always heartwood, never sapwood.
Yes. We travel to every one of the Canary Islands for fitting.
Because wood reacts to moisture. If the screed is too wet or the wood too dry, the floor cups or gaps open up. Measuring takes an hour; a mistake costs the whole floor.
Yes. We glue the floor down over the full surface so the heat reaches the wood with no air gap. We choose timbers that move little, and we only lay once the screed has been heated to protocol and measured dry. Strip and mosaic parquet are particularly suitable, because the short pieces spread the movement of the wood.
In herringbone the strips meet at right angles and the ends are square. In chevron the ends are cut at an angle and the strips form one continuous point.
Often, yes. A solid floor can be sanded several times. We check moisture, firmness and the remaining wear layer, and tell you honestly whether restoring or relaying makes more sense.
It depends on the timber, format, pattern, subfloor and travel. Herringbone takes more time and offcuts than floorboards; an uneven screed takes more preparation. We look at the room, measure and then send you a quote.